P230/4
Descrizione
4 SIDED MOULDER P 230/4
- 1st planer spindle
- 2nd right router spindle
- 3rd left router spindle
- 4th upper horizontal spindle
Technical data:
| - Planer spindle motor power (1° unit) | HP 5,5 |
| - Rh router spindle motor power (2° unit) | HP 5,5 |
| - Lh router spindle motor power (3° unit) | HP 5,5 |
| - Upper horizontal spindle motor power (4° unit) | HP 7,5 |
| - Feed motor power with adjustment by inverter | HP 2 |
| - Traverse lifting motor power | HP 0,5 |
| - Max. working width (with tool dia 125 mm) | mm 230 |
| - Min. working width (with tool dia 125 mm) | mm25 |
| - Max working height (with tool dia 125 mm) | mm 130 |
| - Min working height (with tool dia 125 mm) | mm 8 |
| - Min. workpiece length (single piece) | mm 400 |
| - Feed speed with inverter | 4-20 m/1' |
| - Spindle rotation speed | rpm 6000 |
| - Drive rollers dia (toothed and rubber-coated) | mm 130 |
| - Toolholder spindle dia | mm 40 |
| - Planing tools dimension (horizontal) | mm 125 x 230 |
| - Planing tools dimension (vertical) | mm125 x 130 |
| - Suction inlets dia (4 pcs) | mm 120 |
| - 1° unit tool diameter | mm 125 |
| - Min./Max moulding tools diameter | mm 110-180 |
| - Max tools diameter under the worktable (on vertical spindles) | mm 160 |
| - Max tool groove diameter | mm 160 |
| - Voltage | V. 380/40-HZ 50-3PH+N |
CE equipment:
- Monoblock basement made of properly ribbed steel
- Infeed table made of tubular steel, length mm 2300
- Ply-v belts drive on all spindles, they bear the best efficiency of motors power
- Independent motor unit on each work unit
- Upper traverse equipped with motorized vertical movement, with drive rollers and pressing devices adjustable simultaneously with the upper spindle for higher speed and easier setup
- Feeding system by means of universal joints and single chain and 2-speed motor (7-14 mtr/1’)
- Drive by means of 4 gear wheels and 1 upper rubber wheel in outfeed
- Blowers on the table to optimize wood sliding
- Vertical lh spindle adjustable simultaneously with pressure unit and outfeed guide, for higher speed and easier setup
- Pre-straightening system on the rh side by means of pre-grooving cutter head ( upon request ) mounted on planner spindle
- Decimal precision reading 0,1 mm of 3°-4° spindle displacements
- Quick tool adjusting system on 2°-3°-4° unit
- Possibility to mount cutters on 2°-3°-4° spindle up to a max. diameter of 180mm and a min. diameter of 110 mm (max. moulding diameter 160mm)
- Radial adjustment 2°-3°-4° spindle by means of controls situated on machine front
- Vertical router travel -40mm under the worktable with max cutter diameter 160mm
- Pneumatic pre-planer roller with exclusion on control panel
- Pneumatic pressure on drive units
- Manual worktable lubrication
- Direct motor start by light push-buttons from control panel
- Soundproof protection cabin complete with safety micro-switches
- Control panel with magnetothermal protection
- Lockable main switch
- 2 pcs emergency push-buttons
- Low voltage auxiliary circuit
- Service keys
- Hood room light
Optional:
| SET OF TOOLS
|
| PRE-GROOVING CUTTER HEAD (throwaway cutters) |
| PLANING CUTTER HEAD 230 x 125 x 40 (horizontal spindles) |
| PLANING CUTTER HEAD 130 x 100 x 35 (vertical spindles) |
| KNIFE-SETTING GAUGE |
| UL/CSA RULE |
| VOLT DIFFERENCE 220 AND SPECIAL VOLTAGES |
| AUTOMATIC WORKTABLE LUBRICATION |
| CENTRALIZED LUBRICATION OF GUIDES by means of hand-operated pump |
| CENTRALIZED LUBRIC.GUIDES by means of pump operated from control panel |
| AUTOMATIC AIR AND OIL AUTOMIZER |
| ADDITIONAL DRIVE SPINDLE EXTENSIONE IN FRONT OF 3° UNIT, COMPLETE WITH GEAR WHEEL 45mm |
| ADDITIONAL FEEDING DEVICE FOR SHORT PIECE (mounted in front of RH sp.):
|
| add. GEAR WHEEL thickness 18mm |
| add. GEAR WHEEL thickness 45mm |
| add. RUBBER WHEEL thickness 20mm |
| add. RUBBER WHEEL thickness 50mm |
| MOTORIZED ADJUSTMENT OF 3° UNIT (working width) complete with electrical motor and push-buttons (opening/closing) and decimal adjustment by means of 1 electronic value display with leds |
| ELECTRONIC DISPLAY with leds for height work measurement |
| ELECTRONIC CONTROL 2 AXES: automatic control of left vertical spindle and upper horizontal spindle positioning. Automatic start of all motors included feeding motor. PLC colour display. Min. working width 12mm. |
| AUTOMATIC PRE-PLANER EXCLUSION DEVICE at the first drive group entry |
| SPEED VARIATOR WITH INVERTER kW 2,2 (HP3) |
| 1° PLANER MOTOR KW 5,5 (HP 7,5) |
| RH SPINDLE MOTOR KW 5,5 (HP 7,5) |
| LH SPINDLE MOTOR KW 5,5 (HP 7,5) |
| UNIVERSAL MOTOR kW 5,5 (HP 7,5) |
| KIT OF RINGS composed by rings of different thickness for an overall length 200mm |
| MIN. WORKING WIDTH 15mm WITH NO. 2 STEEL ROLLERS THICKNESS 10mm |
| HOOD COMPLETE WITH INFEED AND OUTFEED PRESSING DEVICES ON UNIVERSAL |