P230/5U

p230_5u
p230_5u2
p230_5u 1
Add product to the quotation

Description

4 SIDED MOULDER P 230/5U

  • 1st planer spindle
  • 2nd right router spindle 
  • 3rd left router spindle
  • 4th upper horizontal spindle
  • 5th universal spindle

Technical data:

-  Planer spindle motor power (1° unit) HP 5,5
-  Rh router spindle motor power (2° unit) HP 5,5
-  Lh router spindle motor power (3° unit) HP 5,5
-  Upper horizontal spindle motor power (4° unit) HP 7,5
-  Universal spindle motor power (5° unit) HP 5,5
-  Feed motor power with adjustment by inverter HP 2
-  Traverse lifting motor power  HP 0,5
-  Max. working width (with tool dia 125 mm) mm 230
-   Min. working width (with tool dia 125 mm) mm25
-   Max working height (with tool dia 125 mm) mm 130
-   Min working height (with tool dia 125 mm) mm 8
-   Min. workpiece length (single piece) mm 400
-  Feed speed with inverter  4-20 m/1'
-  Spindle rotation speed rpm 6000
-  Drive rollers dia (toothed and rubber-coated) mm 130
-  Toolholder spindle dia mm 40
-  Planing tools dimension (horizontal) mm 125 x 230
-   Planing tools dimension (vertical) mm125 x 130
-  Suction inlets dia (4 pcs) mm 120
-  1° unit tool diameter  mm 125
- Min./Max moulding tools diameter mm 110-180
-  Max tools diameter under the worktable (on vertical spindles) mm 160
-  Max tool groove diameter mm 160
-  Voltage V. 380/40-HZ 50-3PH+N                                 

CE equipment:

 

  • Monoblock basement made of properly ribbed steel
  • Infeed table made of tubular steel, length mm 2300
  • Poly-v belts drive on all spindles, they bear the best efficiency of motors powers
  • Independent motor unit on each work unit
  • Upper traverse equipped with motorized vertical movement, with drive rollers and pressing devices adjustable simultaneously with the upper spindle for higher speed and easier setup
  • Feeding system by means of universal joints,double back chain and speed variator with inverter
  • Drive by means of 4 gear wheels and 1 rubber wheel in outfeed
  • Blowers on the table to optimize wood sliding
  • Vertical lh spindle adjustable simultaneously with pressure unit and outfeed guide, for higher speed and easier setup
  • Pre-straightening system on the rh side by means of pre-grooving cutter head (upon request) mounted on planer spindle
  • Decimal precision reading 0,1 mm of 3° - 4° - 5° spindle displacements
  • Quick tool adjusting system on 2° - 3° - 4° 5° unit
  • Possibility to mount cutters on 2° - 3° - 4° - 5° spindle up to a max. diameter of 180mm and a min. diameter of 110mm (max. moulding diameter 160mm)
  • Radial adjustment 2°-3°-4° spindle by 35mm by means of controls situated on machine front
  • Vertical router travel -40mm under the worktable with max cutter diameter 160mm
  • Pneumatic pre-planer roller with exclusion on control panel
  • Pneumatic pressure on drive units
  • Manual worktable lubrication
  • Direct motor start by light push-buttons from control panel
  • Soundproof protection cabin complete with safety micro-switches
  • Control panel with magnetothermal protection
  • Lockable main switch
  • 2 pcs emergency push-buttons
  • Low voltage auxiliary circuit
  • Service keys
  • Hood room light

Optional:

SET OF TOOLS

  • 2 pcs. lanning cutter heads 130 x 125 x 40
  • 2 pcs. lanning cutter heads 230 x 125 x 40
  • 1 pc. Pre-grooving cutter head 12 x 145 x 40 (throwaway cutters)
  • 1 pc. Knife-setting gauge

PRE-GROOVING CUTTER HEAD (throwaway cutters)

PLANING CUTTER HEAD 230 x 125 x 40 (horizontal spindles)

PLANING CUTTER HEAD 130 x 100 x 35 (vertical spindles)

KNIFE-SETTING GAUGE

UL/CSA RULE

VOLT DIFFERENCE 220 AND SPECIAL VOLTAGES

AUTOMATIC WORKTABLE LUBRICATION

CENTRALIZED LUBRICATION OF GUIDES by means of hand-operated pump

CENTRALIZED LUBRIC.GUIDES by means of pump operated from control panel

AUTOMATIC AIR AND OIL AUTOMIZER

ADDITIONAL DRIVE SPINDLE EXTENSIONE IN FRONT OF 3° UNIT, COMPLETE WITH GEAR WHEEL 45mm

ADDITIONAL FEEDING DEVICE FOR SHORT PIECE (mounted in front of RH sp.):

  • Min. working length of single work-piece: 400 mm
  • Min. pushing working length with short pieces device: 200mm

add. GEAR WHEEL thickness 18mm

add. GEAR WHEEL thickness 45mm

add. RUBBER WHEEL thickness 20mm

add. RUBBER WHEEL thickness 50mm

MOTORIZED ADJUSTMENT OF 3° UNIT (working width) complete with electrical motor and push-buttons (opening/closing) and decimal adjustment by means of 1 electronic value display with leds

ELECTRONIC DISPLAY with leds for height work measurement

ELECTRONIC CONTROL 2 AXES: automatic control of left vertical spindle and upper horizontal spindle positioning. Automatic start of all motors included feeding motor. PLC colour display. Min. working width 12mm.

AUTOMATIC PRE-PLANER EXCLUSION DEVICE at the first drive group entry

SPEED VARIATOR WITH INVERTER kW 2,2 (HP3)

1° PLANER MOTOR KW 5,5 (HP 7,5)

RH SPINDLE MOTOR KW 5,5 (HP 7,5)

LH SPINDLE MOTOR KW 5,5 (HP 7,5)

UNIVERSAL MOTOR kW 5,5 (HP 7,5)

KIT OF RINGS composed by rings of different thickness for an overall length 200mm

MIN. WORKING WIDTH 15mm WITH NO. 2 STEEL ROLLERS THICKNESS 10mm

HOOD COMPLETE WITH INFEED AND OUTFEED PRESSING DEVICES ON UNIVERSAL