P240/4

p240_48
p240_49
Add product to the quotation

Description


4 SIDED MOULDER    P 240/4

  • 1st planer spindle (Motor HP 5,5)
  • 2nd right router spindle (Motor HP 5,5)
  • 3rd left router spindle (Motor HP 5,5)
  • 4th upper horizontal spindle (Motor HP 7,5)

Technical data:

- Feed motor power with adjustment by inverter

HP 2

- Traverse lifting motor power

HP 0,75

- Max. working width (with tool dia 125 mm)

mm 240

- Min working width (with tool dia 125 mm)

mm 25

- Max working height (with tool dia 125 mm)

mm 180

- Min working height (with tool dia 125 mm)

mm 8

- Min workpiece length (single piece) 

mm 490

- Feed speed with inverter

4-20 m/1’

- Spindle rotation speed

rpm  6000

- Drive rollers dia (toothed and rubber-coated)

mm 130

- Toolholder spindle dia

mm 40

- Planing tools dimensions (horizontal)

mm 125 x 250

- Tools dimensions (vertical)

mm 125 x 180

- Suction inlets dia (4 pcs)

mm 140

- 1° unit tool diameter

mm 125

- Min/max moulding tools diameter

mm 110-200

- Max tools diameter under the worktable (on vertical spindles)

mm 160

- Max tool groove diameter

mm 160

- Voltage

V.380/40-HZ 50-3PH+N

CE equipment:

  • Monoblock basement made of properly ribbed steel
  • Infeed table made of tubular steel, length mm 2500
  • Poly-v belts drive on all spindles, they bear the best efficiency of motors powers
  • Independent motor unit on each work unit
  • Upper traverse equipped with motorized vertical movement, with drive rollers and pressing devices adjustable simultaneously with the upper spindle for higher speed and easier setup
  • Feed system by means of universal joints, double back chain and speed variator with inverter
  • Upper drive supported by double column
  • Drive by means of 4 gear wheels and 5 upper rubber wheels in outfeed
  • Blowers on the table to optimize wood sliding
  • Vertical lh spindle adjustable simultaneously with pressure unit and outfeed guide, for higher speed and easier setup
  • Pre-straightening system on the rh side by means of pre-grooving cutter head (upon request) mounted on planer spindle
  • Decimal precision reading 0,1 mm of 3° - 4° spindle displacements
  • Quick tool adjusting system on 2° - 3° - 4° unit
  • Possibility to mount cutters on 2° - 3° - 4° spindle up to a max. diameter of 200mm and a min. diameter of 110mm (max. moulding diameter 160mm)
  • Axial rh and lh router adjustment from 0mm up to -90mm by means of controls situated on the machine front
  • Radial adjustment 2° spindle by 35mm
  • Radial pressing device adjustment 3° unit compared with the spindle by 35 mm (to compensate diam.)
  • Axial adjustment of 4° spindle by 40mm
  • Radial adjustment of 4° spindle by 35mm (for diameter compensation)
  • Max tool diameter: 200mm over the worktable and 160mm under the worktable
  • Pneumatic pre-planer roller with exclusion on control panel
  • Pneumatic pressure on drive units
  • Manual lubrication of worktable
  • Direct motor start by light push-buttons from control panel
  • Soundproof protection cabin complete with safety micro-switches
  • Control panel with magnetothermal protection
  • Lockable main switch
  • 2 pcs emergency push-buttons
  • Low voltage auxiliary circuit
  • Service key
  • Hood room light

Optional:

SET OF TOOLS

  • 2 pcs. lanning cutter heads 180 x 125 x 40
  • 2 pcs. lanning cutter heads 250 x 125 x 40
  • 1 pc. Pre-grooving cutter head 12 x 145 x 40 (throwaway cutters)
  • 1 pc. Knife-setting gauge

PLANING CUTTER HEAD 250 x 125 x 40 (horizontal spindles)

PLANING CUTTER HEAD 180 x 125 x 40 (vertical spindles)

UL/CSA RULE

VOLT DIFFERENCE 220 AND SPECIAL VOLTAGES

AUTOMATIC WORKTABLE LUBRICATION

CENTRALIZED LUBRICATION OF GUIDES by means of hand-operated pump

CENTRALIZED LUBRIC.GUIDES by means of pump operated from control panel

CENTRAL.LUBRIC. VERTICAL SPINDLES by means of hand-operated pump

CENTRAL.LUBRIC.VERTICAL SPINDLES by means of pump operated from control panel

AUTOMATIC AIR AND OIL AUTOMIZER

ADDITIONAL DRIVE SPINDLE EXTENSIONE IN FRONT OF 3° UNIT, COMPLETE WITH GEAR WHEEL 45mm

ADDITIONAL FEEDING DEVICE FOR SHORT PIECE (mounted in front of RH sp.):

  • Min. working length of single work-piece: 400 mm
  • Min. pushing working length with short pieces device: 200mm

add. GEAR WHEEL thickness 18mm

add. GEAR WHEEL thickness 45mm

add. RUBBER WHEEL thickness 20mm

add. RUBBER WHEEL thickness 50mm

MOTORIZED ADJUSTMENT OF 3° UNIT (working width) complete with electrical motor and push-buttons (opening/closing) and decimal adjustment by means of 1 electronic value display with leds

ELECTRONIC DISPLAY with leds for height work measurement

ELECTRONIC CONTROL 2 AXES: automatic control of left vertical spindle and upper horizontal spindle positioning. Automatic start of all motors included feeding motor. PLC colour display. Min. working width 12mm.

ELECTRONIC CONTROL 4 AXES: automatic control of right vertical spindle in vertical and left vertical spindle in vertical and horizontal and upper horizontal spindle positioning. Automatic start of all motors included feeding motor. PLC colour display. Min. working width 12mm.

Axial RH and LH spindle adjustment -80mm instead of -90mm

AUTOMATIC WORKPIECE WIDTH SEARCHING DEVICE obtained by means of automatic displacement of 3° spindle; it offers the possibility to work in sequence

panels with different widths. The system is driven by ball-recirculating screw which can be disconnected by means of control on control panel

AUTOMATIC PRE-PLANER EXCLUSION DEVICE at the first drive group entry

SPEED VARIATOR WITH INVERTER kW 2,2 (HP3)

PRE-GROOVING CUTTER HEAD (throwaway cutters)

KNIFE-SETTING GAUGE

SPLITTED PNEUMATIC PRESSURE ON DRIVE ROLLERS

BASEMENT TABLES IN HARDOX HB400

1° PLANER MOTOR KW 5,5 (HP 7,5)

1° PLANER MOTOR KW 7,5 (HP 10)*

RH SPINDLE MOTOR KW 5,5 (HP 7,5)

RH SPINDLE MOTOR KW 7,5 (HP 10)*

LH SPINDLE MOTOR KW 5,5 (HP 7,5)

LH SPINDLE MOTOR KW 7,5 (HP 10)*

UPPER HORIZONTAL MOTOR kW 7,5 (HP 10)*

UPPER HORIZONTAL MOTOR kW 9 (HP 12)*

2° LOWER HORIZONTAL MOTOR kW 5,5 (HP 7,5)

2° LOWER HORIZONTAL MOTOR kW 7,5 (HP 10)*

2° LOWER HORIZONTAL MOTOR kW 9 (HP 12)*

UNIVERSAL MOTOR kW 5,5 (HP 7,5)

UNIVERSAL MOTOR kW 7,5 (HP 10)*

UNIVERSAL MOTOR kW 9 (HP 12)*

REMOTE MOBILE CONTROL DEVICE FOR DRIVE ADJUSTMENT

AUTOMATIC Δ / Y START FOR THE SINGLE TOOL MOTOR *(it's obligatory for 10HP/12HP/15HP/20HP motor)

DRIVE SYSTEM OPERATED BY GEARCASES WITH INCREASED REDUCER AND 2,2 kW INVERTER - FEED SPEED 4-30mt/1'

HOOD COMPLETE WITH INFEED AND OUTFEED PRESSING DEVICES ON UNIVERSAL SPINDLE FOR PLANING AND ROUTING AS 2° UPPER

STRIP RECOVERY GUIDE

KIT OF RINGS composed by rings of differents thickn.for an overall length 200mm

MIN. WORKING WIDTH 15mm WITH NO. 2 STEEL ROLLERS THICKNESS 10mm