PROF 180

prof 180 r
prof180
Add product to the quotation

Description

4 SIDED PLANER PROF 180

  • 1st planer spindle
  • 2nd right router spindle 
  • 3rd left router spindle
  • 4th upper horizontal spindle

Technical data:

-  Planer spindle motor power (1° unit) HP 5,5
-  Rh router spindle motor power (2° unit) HP 5,5
-  Lh router spindle motor power (3° unit) HP 5,5
-  Upper horizontalspindle motor power (4° unit) HP 5,5
-  Feed motor power HP 2 / 1,4
-  Traverse lifting motor HP 0,5
-  Max. working width (with tool dia 125 mm) mm 180
-  Min. worhing width (with tool dia 125 mm) mm25
-  Max. working height (with tool dia 125 mm) mm 130
-  Min. working height (with tool dia 125 mm) mm 8
-  Min. workpiece length (single piece) mm 270
-  Spindle rotation speed rpm 6000
-  Drive rollers dia (tothed and rubber-coated) mm 130
-  Toolholder spindle dia mm 35
-  Planing tools dimension (horizontal) mm 100 x 190
-  Tools dimensions (vertical) mm100 x 130
-  Suction inlets dia (nr. 4) mm 120
-  Voltaggio  V. 380/40-HZ 50-3PH+N                                 

CE equipment:

  • Monoblock basement made of properly ribbed steel
  • Infeed table made of tubular steel, length mm 1700
  • Ply-v belts drive on all spindles, they bear the best efficiency of motors power
  • Independent motor unit on each work unit 
  • Upper traverse equipped with motorized vertical movement, with drive rollers and pressing devices adjustable simultaneously with the upper spindle for higher speed and easier setup 
  • Feeding system by means of universal joints and single chain and 2-speed motor (7-14 mtr/1’)
  • Drive by means of 4 gear wheels and 1 upper rubber wheel in outfeed 
  • Blowers on the table to optimize wood sliding 
  • Vertical lh spindle adjustable simultaneously with pressure unit and outfeed guide, for higher speed and easier setup  
  • Pre-straightening system on the rh side by means of pre-grooving cutter head ( upon request ) mounted on planner spindle
  • Decimal precision reading 0,1 mm of 3°-4° spindle displacements
  • Pneumatic pre-planer roller with exclusion on control panel
  • Manual worktable lubrication 
  • Direct motor start by light push-buttons from control panel
  • Soundproof protection cabin complete with safety micro-switches 
  • Control panel with magnetothermal protection 
  • Lockable main switch
  • 2 pcs emergency push-buttons
  • Low voltage auxiliary circuit
  • Service keys

Optional:

SET OF TOOLS FOR PROF 180

  • 2 pcs. lanning cutter heads 130 x 100 x 35
  • 2 pcs. lanning cutter heads 190 x 100 x 35
  • 1 pc. Pre-grooving cutter head 12 x 120 x 35 (throwaway cutters)
  • 1 pc. Knife-setting gauge (IF NEED BE)

PRE-GROOVING CUTTER HEAD (throwaway cutters) 12 x 120 x 35 

PLANING CUTTER HEAD 190 x 100 x 35 (horizontal spindles)

PLANING CUTTER HEAD 130 x 125 x 40 (vertical spindles)

UL/CSA RULE

VOLT DIFFERENCE 220 AND SPECIAL VOLTAGES

AUTOMATIC WORKTABLE LUBRICATION

AUTOMATIC AIR AND OIL AUTOMIZER

ADDITIONAL DRIVE SPINDLE EXTENSIONE IN FRONT OF 3° UNIT, COMPLETE WITH GEAR WHEEL 45mm

ADDITIONAL FEEDING DEVICE FOR SHORT PIECE (mounted in front of RH sp.):

  •  Min. working length of single work-piece: 270 mm
  •  Min. pushing working length with short pieces device: 200mm

add. GEAR WHEEL thickness 18mm

add. GEAR WHEEL thickness 45mm

add. RUBBER WHEEL thickness 20mm

add. RUBBER WHEEL thickness 50mm

PNEUMATIC PRESSURE ON DRIVE UNITS (FOR PROF 180)

MOTORIZED ADJUSTMENT OF 3° UNIT (working width) complete with electrical motor and push-buttons (opening/closing) and decimal adjustment by means of 1 electronic value display with leds

ELECTRONIC DISPLAY with leds for height work measurement

ELECTRONIC CONTROL 2 AXES: automatic control of left vertical spindle and upper horizontal spindle positioning. Automatic start of all motors included feeding motor. PLC colour display. Min. working width 12mm.

AUTOMATIC PRE-PLANER EXCLUSION DEVICE at the first drive group entry

SPEED VARIATOR WITH INVERTER kW 1,5 (HP2)

KNIFE-SETTING GAUGE (FOR PROF 180)

KNIFE-SETTING GAUGE (FOR PROF 230)

1° PLANER MOTOR KW 5,5 (HP 7,5)

RH SPINDLE MOTOR KW 5,5 (HP 7,5)

LH SPINDLE MOTOR KW 5,5 (HP 7,5)

UPPER HORIZONTAL MOTOR kW 5,5 (HP 7,5)

FEED SYSTEM BY DOUBLE CHAIN AND DOUBLE PINION

KIT OF RINGS composed by rings of different thickness for an overall length 200mm

MIN. WORKING WIDTH 15mm WITH NO. 2 STEEL ROLLERS THICKNESS 10mm